Advanced materials and structures V : selected, peer reviewed papers from the Fifth International Conference on Advanced Materials and Structures (AMS 2013), October 24-25, 2013, Timișoara, Romania

Advanced materials and structures V : selected, peer reviewed papers from the Fifth International Conference on Advanced Materials and Structures (AMS 2013), October 24-25, 2013, Timișoara, Romania / edited by Mircea Nicoara and Carmen Opris.

Collection of selected, peer reviewed papers from the the Fifth International Conference on Advanced Materials and Structures (AMS 2013), 24-25 October 2013, Timişoara, Romania. The 56 papers are grouped as follows: Chapter 1: Advanced Materials, Chapter 2: Materials Characterization, Chapter 3: Mo...

Full description

Saved in:
Bibliographic Details
Corporate Author: International Conference on Advanced Materials and Structures Timişoara, Romania
Other Authors: Nicoară, Mircea (Editor), Opriş, Carmen (Editor)
Format: eBook
Language:English
Published: Pfaffikon, Switzerland ; Enfield, NH : Trans Tech Publications, [2014]
Series:Diffusion and defect data. Solid state phenomena ; v. 216.
Subjects:
Materials > Congresses.
Biomedical materials > Congresses.
TECHNOLOGY & ENGINEERING > Engineering (General)
TECHNOLOGY & ENGINEERING > Reference.
Biomedical materials
Materials
Conference papers and proceedings
Online Access:Click for online access
Table of Contents:
  • Advanced Materials and Structures V; Preface, Committees and Sponsor; Table of Contents; Chapter 1: Advanced Materials; About Replacement of Nickel as Amorphization Element for Fabrication of Ultra-Rapidly Solidified Ti-Zr Alloys; The Effect of Mo and Al on the Corrosion Behavior of Titanium and Some of its Alloys for Biomedical Applications; Structural Characteristics of Ductile Iron at Different Rare Earth Contribution from a Magnesium Ferrosilicon Alloy; Correlation between Microstructure and Magnetic Properties on MnZn Ferrite with Bi2O3 Increasing Addition
  • Composite Powder and Compacts of Iron/Iron Oxide Type Produced by Mechanosynthesis and Reactive SinteringCrystallization of Ni-Cr-Si-B and Ni-Cr-Fe-Si-B Amorphous Alloys; Implant Surface Finishing Influence on Tissue-Implant Anchoring; Mechanical Behavior of Fe60Co14Ga2P10B5Si3Al3C3 Bulk Metallic Glass; The Influence of Sulphur and Oxigen Additions in Mg-Treated Iron on the Cooling Curves Parameters; Research on the Influence of Pelleting Mixture Components on Chemical Components and Pellets Structure; Chapter 2: Materials Characterization
  • Joint Quality Assessment of Three Different Laser Welded Dental AlloysDescription of Degradation Process of Rubberized Lean Concrete; Influence of Cooling Rate on the Structural Characteristics of Ca and Rare Earth Inoculated, Low-S Grey Cast Iron; Influence of the Si-Content on the High Temperature Oxidation Behaviour of NiCrBSi-Coatings; A Study on Metal-Ceramic Thermal Expansion Compatibility; An Evaluation of Sn-Cu-Ga and Sn-Cu-Ag Solder Alloys for Applications within the Electronics Industry
  • Analysis of Hazards Identified within the Premises of the Electric Steelworks, to Carry out the Risk AssessmentComputation of HAZ Hardness for Low Alloyed Welded Steels Using Five-Parameter Logistic Function; Damage Detection in Flux Cored Wire Welded Structures by Using Vibration Testing; Determination of Flexural Properties of Rigid PUR Foams Using Digital Image Correlation; Effects of Silicon Carbide Proportion and Artificial Aging Parameters on Microstructure and Hardness of Al-Cu/SiCp Composites
  • Experimental and Numerical Investigations of TBC Behaviour after Aging, Subjected to Tension and BendingDetermination of Mechanical Properties of Chondrocytes in Articular Cartilage Using Atomic Force Microscopy; Heat Transfer in Composites Subjected to Temperature Variations; Influence of Milling Time on the Homogeneity of the Al2O3/Ni Composite Powders Obtained by Mechanical Milling; Measurement of Young's Modulus and Shear Modulus of Some Structures Welded Using Flux Cored Wire by Vibration Tests

Similar Items